Technical Information
This section provides technical information and allowable service loads for Multibeam Purlin components, including load limits for clips attached to the lip.
Certification & Testing
CE Mark Kingspan Structural Products have been accredited at the highest execution class EXC4, allowing our structural products to be used on all types of construction. The accreditation was carried out by the National Standards Authority of Ireland (NSAI).
Kingspan’s products are manufactured from the highest quality materials to rigorous quality control standards, approved to BS EN ISO 9001. Kingspan’s manufacturing processes are BS EN ISO 14001 (Environmental), 45001 (Occupational Health & Safety) and 37301 (Compliance) accredited.
Physical Properties
Material Specification
All Kingspan Multibeam sections are manufactured from hot dipped galvanised steel to BS EN 10346 and BS EN 10143. The minimum grade of steel used is S450GD, with Z275 zinc coating. Multibeam sections can be supplied with a Magnelis coating. Please contact our sales team for advice.
Dimensions
Kingspan Multibeam Purlins are available in section heights of 145mm to 350mm, standard flange widths of 65 mm to 90 mm and in gauges of 1.2mm to 2.7mm.
To complement the existing Kingspan Structural Products range we now offer 95mm flange sections minimum gauge 1.5mm for use where an insulated panel butt joint is required in the roof. Please see below technical rules for use of the 95mm flange on M175 through M265 sections
View full section dimensions, weights and reference details here.
Multibeam sections are available in lengths of up to 15m.
Performance & Technical Resources
Design Software
We offer industry-leading technical support backed by advanced design software for the design and implementation of our cold rolled steel products. View here.
Load/Span Tables
Load/span tables for Double Span & Single Span Sleeved Systems and Continuous Systems (Heavy End Bay) are available in the Multibeam Technical Handbook.
For single span design capacities, please use the Kingspan Catalyst design software here.
Where Multibeam Purlins are supporting tiled roofs, please refer to the Multibeam Technical Handbook for section capacities and design guidance.
Service Attachments
Clip Attached to the Lip - Purlins
Service loads supported by a clip hung on the lip of the Multibeam or Multichannel should be limited to the value shown in the tables below. All are allowable loads (SLS).
| Table 1.1: Multibeam (65mm flange) and Multichannel (70mm flange) | ||
|---|---|---|
| Section Gauge (mm) | Total Load (kg) | Total Load (kN) |
| 1.2 | 10 | 0.098 |
| 1.3 | 10 | 0.098 |
| 1.4 | 15 | 0.147 |
| 1.5 and above | 20 | 0.196 |
| Table 1.2: Multibeam and Multichannel (90mm flange) | ||
|---|---|---|
| Section Gauge (mm) | Total Load (kg) | Total Load (kN) |
| 1.5 and above | 7 | 0.069 |
| Table 1.3: Multibeam (95mm flange) | ||
|---|---|---|
| Section Gauge (mm) | Total Load (kg) | Total Load (kN) |
| 1.5 and above | 6 | 0.059 |
Other Service Attachments
Where the service load exceeds the capacity of the lip supported clips, other means of attaching the service loads should be adopted.
Wrap around service brackets. These are available from several third-party suppliers, Lindapter, Kaddie, Gripple and others. Capacities and load factors should be sought from the manufacturer.
Direct bolting. Holes can be drilled in the purlin to facilitate attachment of services. We recommend that site drilled holes are limited to 10 mm diameter.
Self-drill self-tapping screws. These may be utilised to produce an attachment point – the manufacturer of the fixing performance values should be consulted.
Shot fired nails. Not normally recommended with cold formed Multibeam and Multichannel sections, but check with the manufacturer of the system for specific guidance.
Environmental
View the EPD for Multibeam Purlin.
View the EPD for Multibeam LEC Purlin
Kingspan Multibeam sections are produced in the UK and Ireland are certified to BES 6001 (Framework Standard for the Responsible Sourcing of Construction Products) ‘Good’.
Details & Drawings
Custom Kingspan components and macros along with instructional videos are available on the Tekla Warehouse.
You can register to download the entire range of Kingspan Revit families from BIM360 using this form.
Downloads
Access product brochures, datasheets, and technical documentation to support specification and project planning.











